iFlight Beast H7 55A AIO 25.5x25.5mm Flight Controller (MPU6000)

iFlight Beast H7 55A AIO 25.5x25.5mm Flight Controller (MPU6000)

The Beast H7 55A AIO is iFlight’s new innovation!

Only 1 left in stock

7,799

iFlight Beast H7 55A AIO 25.5×25.5mm Flight Controller (MPU6000)

7,799

Description

iFlight Beast H7 55A AIO 25.5×25.5mm Flight Controller (MPU6000)

The Beast H7 55A AIO is iFlight’s new innovation! This lightweight AIO FC was designed to make room for flight firmware development like Betaflight, Emuflight, etc. iFlight used BGA chipsets instead of ordinary QFP (big size) MCUs and ultra-powerful Mosfets for almost any build. Solder your motor wires and you are good to go!

Compatible with digital and analog!

Features

  • Vista digital system Plug-and-Play (VBat passthrough)
  • MCU: BGA-STM32H743 , 480MHz
  • OSD: AT7456E
  • Gyro: MPU6000
  • Blackbox: 16Mb Onboard Flash
  • BEC output: 5V 2.5A
  • Barometer: DPS310 (only works with Betaflight 4.3.0 and above)

Safety reminder

The DJI plug&play port has no voltage regulator (BEC) and is passing through VBAT. The Caddx Vista goes up to 26.4V (6S), the DJI Air Unit goes up to 17.6V (4S). Make sure not to plug-in your DJI Air Unit directly when you’re flying 6S, because this would fry it! BEC to add for your 6S build can be found here: https://shop.iflight-rc.com/index.php?route=product/product&product_id=747

Small motor 4S builds should usually need an additional capacitor of at least 16V/220uF, for 6S go up to 35V or even 50V. Bigger motors have a bigger current draw, higher voltage spikes, and more serious back EMF (motor braking, works as a generator). Make sure to add big enough or even bigger low ESR capacitors on the AIO battery pad or on your battery lead the more aggressive motors you fly. There’s a choice of capacitors in the package, but it’s never a bad idea to make sure to protect your board. Smaller boards have less capacitance which has to be covered with external capacitors, there’s no way around it.

IFlight’s new DPS310 Barometer has more accuracy than the older BMP280 before but can not be activated in Betaflight below 4.3.0 which is currently in beta state (December 2020).

Specifications

FC // Beast H7 AIO

  • MCU: BGA-STM32H743
  • Gyro: MPU6000
  • Blackbox: 16Mb Onboard Flash
  • BEC output: 5V 2.5A
  • Barometer: DPS310 (only works with Betaflight 4.3.0 and above)
  • Micro-USB
  • OSD: AT7456E
  • Uart:5 (UART1、UART2、UART3、UART4、UART7)
  • FC Firmware:IFLIGHT_H743_AIO
  • Mounting pattern: 25.5*25.5mm φ3mm
  • Dimensions: 32.5*32.5mm
  • Weight: 8.8g

ESC // 55A 2-6S

  • Uarts: 5
  • Current Sensor: Yes
  • Input: 2-6S LIPO
  • Current scale: 200
  • Constant: 55A / Burst: 60A
  • BLHeli: BLHeli-S
  • Telemetry: no
  • ESC Firmware: BlheliS G-H-30
  • Mounting pattern: 25.5*25.5mm/Φ3mm
  • Dimensions: 32.5*32.5mm

Includes

  • Beast H7 AIO × 1
  • Capacitor 470uF/16V x 1
  • Capacitor 470uF/35V x 1
  • XT60 12AWG cable 100mm x 1
  • XT30U 18AWG cable 70mm x 1
  • 14AWG Silicone Cable Red 100mm x 1
  • 14AWG Silicone Cable Black 100mm x 1
  • 1.0-7P cable 50mm-28mm x 1
  • 1.0-7P cable 50mm x 1
  • M2 silicon grommets x 4
  • M2*12mm screws x 8
  • M2 Transparent Nylon Nut x 8
  • 0.8mm black Heat shrink tube 10mm x 8

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “iFlight Beast H7 55A AIO 25.5×25.5mm Flight Controller (MPU6000)”

 

Get in Touch!

We are here for you !